www.bewet.fora.pl

loczytzn

Iron production in India

Blank ills often in fixed position. In addition to fountain at both ends, the ink rollers at both ends of the plot, and sometimes the skin will produce the phenomenon of ink. Experience has taught us: the field version of the product in India, especially the full version of the ground product, skin prone to the phenomenon of ink: The cable version of the product in India, this phenomenon will alleviate many, this is why? This is because version printed on the ground, color ink consumption of the relatively large amount of ink for the ink part of the ink fountain and ink fountain roller blades large gap between: the Indian cable version of the product,[link widoczny dla zalogowanych], the ink fountain and ink fountain roller blades with smaller spaces. Large amount of space between the ink, the ink leave out the spaces are relatively a little more skin; and the gap is small, some large ink skin is not easy to drain down. Slot in the ink fountain is blocked. Moreover, even a small amount of leakage of human skin ink inking system, the impact is also a part of Patterns, a color version of the child outlets, often not affect the overall patterns in the results. (Of course, the main site or four lines into a color version of the Internet may be relatively larger.) The solution is: 1,[link widoczny dla zalogowanych], selection and use bottled ink in the skin surface is hard to form, good performance of Indian iron printing ink 2, the process for easy iron in India ink conjunctiva can be added in the ink fountain in the amount of ink just dry agent, but less than 1% the amount of control to avoid other negative consequences. 3, found that the skin promptly shut down the ink and blanket wash plates, the ink in the skin to eliminate the harm the beginning, so as not to cause greater impact and affect more of the sheets. Third, due to the aging of rubber roller in the Under normal circumstances, the service life of 1 years. Its life also depends on the Indian iron machine running full load, the pressure regulating inking system whether it is appropriate, whether regular contact with strong solvents factors, operating heavy load, short life, the pressure is too have a greater extrusion pressure, long-term weight The following will shorten the life of the cot. In addition, when the cleaning roller, to avoid using strong solvents such as bananas, water and other organic solvents. The early stage of aging roller surface will appear rough, poor finish phenomenon. Then will appear the phenomenon of rubber wrinkled skin, a serious was the bark-like iron production in India and it is long-term pressure friction with inks, solvents, such as the role of the results. At this time, the rubber has been aging. Rubber aging have many of the small rubber particles flaking off from the ink roller. The operation of the inking system, these tiny particles directly mixed into ink, and then passed through the transfer ink system, enter the plate Patterns in. Transferred to the blanket by the plate, or some still adhere to the plate on Patterns. At this time, plate or blanket in the Patterns of a site, thanks to rubber particles, so that this part of the normal transfer of ink has been hampered both rubber particles and slightly behind the lipophilic part of the printed version of the Patterns; the same time as Rubber-like particles was raised, together with the particles than the flow out from between the ink fountain should be thick skin several times. Therefore,[link widoczny dla zalogowanych], the ink particles around the contact with the corresponding less, that is, a blank circle around the particles formed by the skin than ink greater = blank circle solution: Check in time roller, roller that early replacement of aging, to avoid affecting the product quality. Fourth, transfer ink system caused by bad cleaning agency 1, prior to production, be sure to clean the fountain part, especially the ink fountain roller and ink fountain blade at both ends of the edge of the edge at both ends, often satisfied that the contamination of the local scale,[link widoczny dla zalogowanych], it must be left clear on the scaling of the color ink clean, leaving no traces. Otherwise, the next color in the printing ink,[link widoczny dla zalogowanych], the scaling easily to soften, is likely to emerge from the ink supply part, against the chromatography of the product quality. Be sure to pre-production series roller, transfer ink film on the film roll crust and the elimination of dirty things clean. Found on the dirt and not stick to the timely removal of the ink roller, have taken to cause the ink on the plate patterns in the skin at the same time the possibility of defects in the plate, the blanket also can not leave garbage, or would result in Mexico, the possibility of skin defects. In addition, the process of iron production in India, there is garbage fall any inking system parts, will also have a fixed position (in the Patterns section) of the ink skin defects. The solution is: 1, inking system, each part of a thorough and comprehensive cleaning of work, while thorough, comprehensive cleaning of Indian iron machine parts, plant environmental requirements to keep clean and prevent waste, particle debris and other falling plate , blankets and inking system. 2, found that the skin defects fixed position of the ink, wipe down immediately clear plates and blankets before you can continue to produce short, the order construction, is fully proactive:

相关的主题文章：

christian louboutin shoes Packaging design and adv

[link widoczny dla zalogowanych]

[link widoczny dla zalogowanych]